Catalogue

LG CM18R (18,000 BTU, 5 kW) - medium-static ducted indoor unit 270 mm high

CL-000902
51 98000 ₴
Out of stock
14 days
Our advantages
Delivery terms and cost
Payment options

Description LG CM18R

The CM18R: a 5 kW medium-static ducted unit

The CM18R is a ducted indoor unit of LG's R32 semi-industrial series rated at 5 kW cooling and 5.8 kW heating. It differs from the equally powerful CL18R (item 1826) in casing height: 270 mm instead of 190 mm, at the same 900 mm width and 700 mm depth. The taller construction means a larger fan assembly and therefore higher available static pressure and the ability to work with a long branched duct network. The supply is 220-240 V, 50 Hz, the refrigerant R32, the compressor in the pair a Dual Inverter, the manufacturer country and country of origin Korea and the warranty 24 months. This model's card gives no pipe diameters, maximum pipe run or height difference - those fields hold dashes, and we supply the exact values from LG's combination table.

What static pressure is and why it gets discussed

The fan of a ducted unit creates not merely a flow but a flow under pressure, and that pressure is measured in pascals: it is what overcomes the resistance of ducts, grilles and filter. Low-static units of the CL series are designed for roughly 30-60 Pa, medium-static units for several tens of pascals more, and that difference decides what network the system can serve. If the actual resistance exceeds the available pressure the fan does not stop - it simply moves less air, and the system quietly loses output: the cooling is there but the room does not get cool. The unit's board has a fan speed setting with which the installer matches the mode to the real network at commissioning; that is a mandatory step, not a decorative option. The exact static pressure figures for a specific model come from LG's technical documentation, and we supply them along with the network calculation.

How to estimate the resistance of a duct network

The rough arithmetic looks like this: a metre of correctly sized rigid galvanised duct adds single-figure pascals, a tight bend around 5-10 Pa, a supply grille 10-20 Pa, a return with a filter 20-50 Pa depending on the filter grade. Flexible duct gives several times the resistance of rigid duct of the same diameter, and it is flexible duct that most often eats the whole pressure allowance. When a layout has 6-8 grilles, a long main duct and a filter in the return, the sum easily passes 100 Pa - and at that point a low-static unit no longer fits as a matter of physics rather than preference. These figures are indicative: the exact calculation is made from the tables of the duct and grille manufacturers, and for complex layouts we work it out separately. The rule is simple: the longer and more branched the network, the more pressure headroom has to be allowed for when choosing the unit.

When you need a CM rather than a CL

The first situation is a long main duct: if the distance from the unit to the farthest grille exceeds 8-10 metres, or the layout has more than four bends, medium static pressure becomes essential. The second is several rooms from one unit: three or four offices on the same regime, a corridor layout, a hotel floor with rooms on one circuit. The third is filtration: if a finer cassette filter is fitted in the return duct for a medical room or an office, its resistance has to be overcome by something. The fourth is fresh-air mixing: a duct from outside with a damper and a filter adds resistance that a low-static unit will not take. And the fifth is practical: if the duct layout is not final and may change during the fit-out, pressure headroom is insurance against rework.

Ceiling void for a 270 mm casing

A height of 270 mm means at least 380-420 mm of void above the suspended ceiling: hangers with isolators, a drain line with a fall and pipe insulation are added to the casing. That is more than the CL series needs, and this is where conflicts with beams, ventilation ducts or room height most often arise. Before choosing the unit it is worth measuring the actual distance from the slab to the planned ceiling level at the spot where the unit will sit, not the average across the room. An inspection hatch of at least 450 by 450 mm is mandatory on the side of the filter and the electrical box; for a medium-static unit it is more convenient to make the hatch wider, because access to the duct connections is needed too. If the height is not there, the alternatives are the CL18R (item 1826) with a simpler network or the CT18R cassette (item 1836), which needs less void.

Pairing with an outdoor unit

By output the CM18R pairs with the UU18WR outdoor unit (item 1814) at 5 kW cooling and 5.8 kW heating, single-phase, in a casing of 870 by 650 by 330 mm. The circuit runs on R32; as the indoor unit's card gives no pipe diameters or maximum lengths, we take them from the manufacturer's documentation for the specific pair and state them with the proposal. The current of such a system at 220-240 V is roughly 7-9 A: a dedicated circuit with a breaker is enough without raising the authorised capacity. The outdoor unit is positioned with 1-1.5 metres of clear space in front of the fan and access to the service panel on the electrical box side. We verify the combination against LG's compatibility table: the pair has to appear in the manufacturer's documentation, otherwise the system's warranty is in question.

Which jobs it fits and where it is out of place

The CM18R is the choice for a space of roughly 45-55 m², or for several adjoining rooms on the same regime, where the ductwork is long, the network branched, or the layout includes a filter and fresh-air mixing. It is chosen for medical rooms, offices with several rooms, hotel floors, salons with back-of-house areas. Where the model is out of place: spaces with less than 380 mm of void - the CL18R (item 1826) or a cassette is needed there; a simple layout with one or two grilles, where paying for static pressure makes no sense; spaces with several zones needing different temperatures. A restaurant kitchen or a production area with high heat gains needs different equipment and a separate ventilation calculation. And if the area exceeds 60 m², you move to the CM24R (item 1829) or the UM series.

How it differs from neighbouring models in this catalogue

The CL18R (item 1826) is the same 5 kW at 190 mm high and low static pressure: slimmer and cheaper to install, but only for a simple network. The CM24R (item 1829) is medium-static 7 kW in the same 270 mm high casing: the next step in capacity. The CL24R (item 1827) is 7 kW low-static in an 1100 mm casing. If there is no suspended ceiling at all, 5 kW is available from the CT18R cassette (item 1836) or the MJ18PC wall unit of a multi-split system (item 1873). The outdoor unit for this model is the UU18WR (item 1814), the same one that works with the CL18R and the CT18R, so the indoor type is chosen for the space rather than for the outdoor side.

Describe the duct layout you are planning - we will calculate the network resistance and say whether the CM18R's medium static pressure is needed or the CL18R will do.

Characteristics LG CM18R

Installation type
Канальний
Electrical properties
Current frequency
50Hz
High-voltage
220 - 240В.
General characteristics
Appointment
Напівпромисловий
BTU
17
Compressor type
Dual Inverter
Country of origin
Корея
Country of origin
Корея
Guarantee
24 months
Refrigerant
R32
Type
Split system
Manufacturer
LG
Overall dimensions
Indoor unit height
270 mm.
Indoor unit length
700 мм.
Indoor unit width
900 мм.
Physical properties
Material of execution
Combination of metal and plastic
Thermal properties
Cooling capacity
5000 Вт.
Thermal efficiency
5800 Вт.
Find similar

Reviews about LG CM18R from real users

No reviews found

Store addresses
Working hours
Телефон
Availability
Maybe it will interest you
  • Recently viewed
  • Most popular
  • Sale
 
 
 
Швидко і якісно достявляємо

Наша компанія виконує доставку по всій Росії і ближньому зарубіжжі

Гарантія якості і сервісне обслуговування

Ми пропонуємо тільки ті товари, в якості яких ми впенені

Повернення товару протягом 30 днів

У вас є 30 днів, для того щоб протестувати вашу покупку